HIS AND HERS LAPTOP SLEEVES

These laptop sleeves would make the perfect gift for your techie friend or family member this Christmas. These sleeves can be sewn in under an hour and are easy enough for the beginner sewer.

PLEASE NOTE: these designs are solely for domestic use and cannot be used commercially or sold. 

WOMEN'S LAPTOP SLEEVE

Supplies:

2 pieces of felt in contrasting colours – 18” x 26”

1 piece of white felt 3” x 14”

18” x 26” fusible webbing  

¾” x 6” Velcro

White and grey thread

Method:

1) Measure the width of the laptop.  Cut 2 pieces of felt approximately 2 inches wider than the laptop and 26” long.

2) Cut 1 piece of fusible webbing to the same size.

3) Cut 3 strips of white felt 1” wide at varying lengths. 

4) Cut each strip in half at an angle.

5) Pin white strips to the front of the sleeve and sew in place.

6) Pin Velcro 4” from opposite edge and sew in place.

7) Pin and sew second strip of Velcro approximately 1” from edge of lining felt. (Note: distance will vary depending on laptop. Fold felt over laptop to mark placement of second strip correctly.)

8) Sandwich the fusible webbing between the 2 layers of felt and fuse according to packaging instructions.  The two strips of Velcro should be at opposite ends of rectangle.

9) Sew edges of felt.

10) With wrong sides together, fold felt approximately 1” shorter than the height of laptop.

11) Sew a 3/8” seam along folded edges. 

MEN'S LAPTOP SLEEVE

Supplies:

2 pieces of felt  - 18” x 26”

1 piece fusible webbing - 18” x 26”

¾” x 18” elastic

Grey thread

Method:

1) Measure the width of the laptop.  Cut 2 pieces of felt approximately 2 inches wider than the laptop and 26” long.

2) Cut 1 piece of fusible webbing to the same size.

3) Sandwich the fusible webbing between the 2 layers of felt and fuse according to package instructions.

4) Sew edges of felt.

5) Cut a piece of elastic to the same length as the width of the sleeve + 1” for seam allowance.

6) With wrong sides together, fold felt approximately 1” shorter than the height of laptop.

7) Sandwich edges of elastic between felt.

8) Sew 3/8” seam along folded edges.  

Have fun creating your own Christmas gifts this season. Nicole 

FALL FASHION REPURPOSED: Crop top and high-waisted skirt DIY

With temperatures dropping in San Diego, I started riffling through my closet for some autumn-appropriate clothing.  Finding very little that excited me, and even less that still fit, I was feeling  defeated.  I was resigned to the fact that I’d be raiding my husband’s side of the closet for the next few months.  That was until I stumbled upon a dress I picked up in a thrift store a few years ago: a double-breasted knit dress.  I no longer wore it, and I had long contemplated getting rid of it, but the dress still had potential.  I love to reimagine or reinvent something that I already own, giving it a new life and saving it from the landfill.  This dress seemed the perfect candidate.  I decided to make it into a little cropped top and high-waist skirt, similar to one I saw Solange Knowles wearing.  (Yes, the girl who wears khakis and hiking boots for a living occasionally reads fashion blogs!)  

There was only one problem: I had never sewn anything more than a hem, so this was going to be a steep learning curve.  It turned out it wasn’t so hard after all and I’m thrilled with the end result.  My new (old) outfit is perfect for San Diego’s mild autumn.

Supplies:

Knit dress

8” wide coordinating knit fabric (length approx. = waist measurement + 1” seam allowance)

Thread

Chalk

Scissors

Step 1:

Try the dress on and use chalk to mark your real waist.

Step 2:

Cut the dress in two at real waist marking.

Step 3:

To make the top more fitted I added 2 darts to the front and 2 to the back. 

I used a pattern block to mark the location of my darts.  If you don’t have one available, this handy youtube demonstration will show you how to mark and sew them in the right place. 

Step 4:

Mark and sew two pleats in the front of skirt and two darts in the back. 

Step 5:

Cut two strips of the black knit fabric, one 2” wide (edging for top) and the other 6” wide (waistband).  Calculate the length of strips required by measuring the total length of cut edge of top or skirt and adding 1” for seam allowance. 

Step 6:

Fold strips in half and iron flat.  Fold raw edges in towards center and iron. 

Step 7:

Sandwich the raw edge of your top within the edging.  Pin and sew.

Step 8:

Sandwich the raw edge of the skirt within the waistband.  Pin, sew and you’re done!

I love my new crop top and skirt.  They are so much cuter than my husband’s over-sized sweaters.

 

SHOU SUGI BAN OUTDOOR TABLE DIY

When we needed an outdoor table for our recently completed patio, I figured I would have to build one myself.  A few years ago, my husband Jeremy designed a beautiful table for our front deck.  However, being finished in polyurethane it needed constant maintenance.  As he watched the polyurethane crack and mold grow underneath, he was in no mood to make another.  That was until I uttered the words “Shou sugi ban”.  His eyes immediately lit up.  I had him hooked! 

Shou sugi ban, or Yakisugi, is a traditional Japanese method of burning cedar (sugi) before finishing it with natural oil.  Normally used as exterior siding, the charred wood is pest and rot resistant for up to eighty years.  So, charring is a beautifully simple way of ensuring the longevity of wood.  Here are a few contemporary examples.

Clockwise from top: Fujimori's charred cedar house, Ubon, Hunsett mill, De Noorderparkbar, THOUGHTBARN office, Havet cabinet.

  

Though a few expletives were uttered during the making of this table (which come standard with my husband’s DIY projects), it was easy to make.  Once charred, the wood appears a silvery grey or shiny black depending on how the light hits it.  We love how this table turned out. 

Materials:

Hairpin legs (we bartered for a second-hand set at a local street fair, but you can purchase them new here)

2 laminated pine panels 47 ½ “x 15” x 1 ½ “

2 pieces of pine 27 ½” x 5 ½ “x 1” (supports)

1 Bernzomatic UL100 basic propane torch kit

12 wood screws 1 ¼ “

12 sheet metal screws 1 ¼ “

White Rust-Oleum spray paint

Linseed oil/ other natural oil

Sponge brush

Wood glue

Sand paper 

Drill

Clamps /tie downs

Step 1:

Use sandpaper to remove any rust from the hairpin legs and to help the paint adhere.  Spray paint them in a well-ventilated room.

Step 2:

Glue the two pieces of laminated pine together and clamp.  Let it rest on a clean, flat surface for approximately 2 hours while the glue cures. 

Step 3:

Glue the supporting pieces of pine approx. 5” from the edge of either end of the table.  Evenly space six wood screws along the length of the supports and screw into wood, making sure they go into the base of tabletop.

Step 4:

Assemble the Bernzomatic torch kit according to instructions.  Light and begin burning the wood, following the grain. 

NOTE: Burn the tabletop in an area clear of vegetation. 

Step 5:

Once both sides are sufficiently charred, use a brush or wet rag to wipe off excess soot.

Step 6:

Use the sponge brush to apply several coats of linseed oil to the tabletop.

Step 7:

Use the sheet metal screws to attach legs to tabletop.

Sit back and enjoy your new table:) Thanks for visiting. Nicole

HEXAGONAL TRIVETS DIY

Who knew I would love power tools?  For years my dad worked as a carpenter.  I never thought to ask him how to build things since I figured he would always be there if I ever needed a cabinet or shelves.  So, after relocating to San Diego I found myself in trouble: my dad was in Cape Town, my husband hated home improvement and we had a house that needed a lot of upgrades.  I needed to find someone handy with a saw.  The solution (after much deliberation) was for me to take a carpentry class.  When I enrolled last spring I could have never guessed how much I would love it.  Now, my husband and I have dreamed up so many projects that I’ll need years to finish them all!

These plywood hexagons were originally cut for a project at the hubster’s office (more on that later).  They had been lying in a corner for a few weeks—like many of my projects seem to do—while I contemplated the next step.  With a friend having recently purchased a house, I knew I’d have to come up with a good house-warming gift.  I hit on the idea of using some of the hexagons to make trivets.  I think they are hip, pretty and fun, just like their soon-to-be owner. 

NOTE: These instructions are for making plywood hexagons.  If you have never used a saw (and you don’t want to lose any fingers!), try making the trivets out of cork.  All you’ll need is a utility knife.  

What you’ll need:

¼” or ½” Plywood (at least 10” x 10” for each trivet)

Pencil

Compass

Ruler

Table saw

Miter saw

Sealant (linseed oil or beeswax)

Optional:

Acrylic paint

Painter’s tape

Paintbrushes

Plastic containers

Step 1:  

Draw a hexagon on the plywood. 

The easiest way I found to do this was to use a compass.  Set the compass to a radius of 5” (or larger for a bigger trivet) and draw a circle.  Don’t change the angle of the compass.  Mark a beginning point (A) along the circle. Place the point of the compass on A and mark a second point (B) 5 inches away from A along the circle.  Make sure that a line drawn between point A and point B is parallel to the edge of the plywood.  Continue moving the compass point to the new mark along the circle in order to mark all 6 points of the hexagon.  Once you have all the points marked, connect the dots to create the hexagon. 

Step 2:

Use the table saw to rip (cut with the grain) the wood along the top and bottom of the hexagon.

Step3:

Crosscut the plywood with the miter saw along the outer edge of the hexagon.  

Step 4:

Set the miter saw to 30 degrees and cut the remaining sides of the hexagon.

TIP:  Use the first hexagon as a template to draw the rest.  That way they will all be the same size. 

Step 5:

If you like the natural look, seal the trivet with linseed oil/beeswax to prevent staining. 

To add some colour and designs to the trivet, use acrylic paint and tape before sealing.

Happy crafting!  Nicole